Prev | Next

Working With Multiple Flags

<< | >>

Why Do My Flags Look Identical?

Overview

In this section, you'll create a scene with two flags. At first, they will look identical, but we'll show you how to make subtle changes so each flag looks unique.

Creating A Scene With Two Flags

This section will show you how to create a scene with two flags, both on the same flagpole.

  1. Open the project called "Flagpole Single.aep" found in the "Flag Tutorials" folder. This project was created using techniques discussed in Attaching Your Flag To A Flagpole. The Comp window should look like this image.



    In this picture, the flagpole was part of the background image. This flag is attached to a flagpole layer, but that layer is hidden.
  2. Turn on the visibility of the "Flagpole" Solid layer.



    Now you can see the long, skinny Solid that the flag is attached to. Notice how the "Flagpole" Solid layer has been placed in the scene to cover up the flagpole in the background picture. We use this fake flagpole as our guide, and then turn off its visibility once everything has been oriented properly.
  3. Turn off the visibility of the "Flagpole" Solid layer.

Adding A Second Flag To The Flagpole

  1. Duplicate the "Top Flag" layer by selecting the "Top Flag" layer in the Timeline window and then selecting Edit> Duplicate.
  2. Rename the new layer "Bottom Flag."
    This layer is an exact duplicate of the "Top Flag" layer. This means that the flags are in the same place and are attached to the same flagpole. Let's make the second flag lower on the pole than the first flag.
  3. Open the Effect Controls window (Effect> Effect Controls).
  4. Lower the Offset Y value until one flag is below the other. A value of 225.0 should do the trick.
  5. In the Effect Controls window, select "Red Crescent.jpg" from the Color From Layer menu. You now have two flags on the same pole.



  6. View the first few seconds of the animation by doing a RAM Preview (Composition> Preview> RAM Preview).
  7. Notice how the flags move in exactly the same way. Let's fix this.

Making Flags Unique

While you can probably imagine that changing just about any parameter on one of the flags will make the two flags look different, you'll still want them to look like they're part of the same scene. That is, you'll want them to look like they're receiving the same wind and other forces. You may also want them to look like they're made out of the same material. Choosing the right parameters to change is important.

Let's make the "Red Crescent.jpg" flag similar but different.

  1. Select the "Bottom Flag" layer.
  2. Open the Effect Controls window (Effect> Effect Controls). Since these two flags are so close to each other, we can't change the wind direction, but we can change the wind speed by a small amount. This won't change the overall look, but will help break up the synchronization of the two flags.
  3. Set Wind Speed to 10.5.
  4. View the first few seconds of the animation by doing a RAM Preview (Composition> Preview> RAM Preview). The flags aren't as synchronized as they were before, but they still look too much alike. By changing the Pre-Roll value, we can offset how far along in the animation we are. This will add some uniqueness to the "Bottom Flag."
  5. Set the Pre-Roll value to 3.0. This will differentiate how many frames are calculated for each flag. This will make the flags look different for a few seconds, but it may not help over longer periods of time, when the flags get into their patterned undulation.
  6. View the first few seconds of the animation by doing a RAM Preview (Composition> Preview> RAM Preview). Notice how the flags seem to act independent of one another.

You could probably stop here and have perfectly acceptable results, but let's go a bit further and look at some other ways to make flags different.

Making Flags Even More Unique

  1. Open the Options window by clicking on the 3D Flag logo at the top of the Effect Controls window.
  2. Press the spacebar to pause the animation. Let's make the flag look like it's made of a slightly different material.
  3. Set Flag Stretch, Flag Bend, and Flag Shear each to 5.0.



  4. This makes the flag a little more loose and stretchy. More importantly, it will react to the wind differently than the "Top Flag."

    Click the OK button to close the Options window.



  5. View the first few seconds of the animation by doing a RAM Preview (Composition> Preview> RAM Preview). The flags look like they're reacting to the same wind, but they are flapping in their own unique way.

Deciding Which Parameters To Change

The chart below describes how the different parameters can be used to achieve different looks.

ECW Parameter

How It Can Make Flags Different

Wind Speed

Small differences can help the flags undulate at different rates.

Larger differences can make flags look like they're in different parts of the scene (that is, far away from each other).

Wind Direction

Flags can look like they're in different parts of a scene.

Pre-Roll

By having different Pre-Roll values, flag undulations will occur at different times.

Options Window Parameter

How It Makes Flags Different

Flag Stretch/Bend/Shear

Changes the material of the flag.

Conform

Changes the material of the flag.

Horizontal/Vertical Mesh

Changes the material of the flag.

In the next section, Reusing Animation For Different Flags, you'll learn how changing a single 3D Flag parameter can facilitate the creation of five animations.